DIY Mini Speedster Depron Plane from Flitetest

Above is my new mini speedster plane that i build from depron, it use only 2 cell battery and have nice flying characteristic, very floaty and easy to build

Project Status : Success
Project Time-frame: Mid November 2014
     








  

          Picture from flite test website

 The other three motor has being used as a mini DIY tricopter, for the maiden flight it was a successul and fly nice ..
















Video:
below is my maiden flight video with attached mobius cam with my hat

Picture :

I added few changes like a landing gear, fuselage cover and a LEGO action figure toy to added scale look
here are the photo below

maybe when budget permits i will added mini FPV setup for a pilot's view

http://www.thingiverse.com/thing:327338#sthash.zTzt6Zho.dpuf

Project Summary

This is first plane i ever made from flite test plans, it only use 1/2 depron to build one and the instruction to build is very easy and if you lost, just follow the guide video from Josh from youtube.

from the video you can see the motor seems lack of thrust, i cannot able to make a loop with this motor, soon i will upgrade to a better motor

Spec
one only ZMR@RCX motor 1804 from Myrcmart
-Afro ESC 12 amp simonk
-Turnigy 9xr and 800mah 2 cell
- 5x3 props

when the budget permits i will upgrade it with smallest camera and fpv equipment, i dream to fly it

Project Budget
RM 30.00 and a old mini quad

Parts for the Project

1. ZMR Motor -


http://www.banggood.com/ZMR-1804-2400KV-Micro-Size-Integration-Outrunner-Brushless-Motor-p-923424.html?p=6Q272106433620120652


Source from:
 http://www.flitetest.com/articles/ft-mini-speedster-build

DIY 3D Printed Tricopter with Acro Naze32

Project Summary: To make a fun mini tricopter that can fly indoor and outdoor
Project Status : Success
Project Time-frame: Mid November 2014

  












Pic above from flite test :http://www.flitetest.com/articles/mini-tricptr-3d-printed-tricopter

Video:
below is my maiden flight video with attached mobius cam with my hat

http://www.thingiverse.com/thing:327338#sthash.zTzt6Zho.dpuf

Project Summary

one of the motor from my previous miniquad is being use as powerpod for flitetest mini speedster plane,
The remaining 3 motor is used for my 3d printed tricopter...
This is my first tricopter build and it is also my first maiden of my tricopter

Spec
-3 ZMR@RCX motor 1804 from Myrcmart
-Afro ESC 12 amp simonk
-Acro Naze32
-1300 mah 3cell with 5x3 props

 The most crucial parts of tricopter is how to build a tilt mechanism, it must had a good servo speed and agility .
For maiden flight the first problem that i facing is the quad start spinning one direction only.
the problem is solved after i reverse the servo setting at a Baseflight configurator.

The mini tricopter is fly so fast and agile..but it is a small size and hard to find the orientation once the tricopter flew away. so for my next project is to put FPV equipment for long range flight with this mini

Project Budget
RM 30.00 and a old mini quad

Source from:
http://www.flitetest.com/articles/mini-tricptr-3d-printed-tricopter

http://www.thingiverse.com/thing:327338#sthash.zTzt6Zho.dpuf

http://www.thingiverse.com/thing:327338#sthash.zTzt6Zho.dpuf

http://www.thingiverse.com/thing:327338